SAFER POSI LOCK PULLER OPERATION FOR MANUAL PULLERS: 1. Make sure that all items being pulled are supported by a means other than the puller. NO LOOSE PIECES!!! 2. Before each use, lubricate the center bolt of the puller with a graphite-based lubricant. 3. To operate the puller, grasp the puller with one hand and…

SAFER MECHANICAL PULLER OPERATION: 1. Make sure that the spindle is clean and greased before use. 2. The shaft must have a center hole. If it does not, use a shaft protector 3. Tighten strap bolts to hold jaws lightly in place. 4. Position the puller. 5. Tighten the spindle slightly by turning the spindle…

To avoid personal injury during system operation, read and follow all CAUTIONS, WARNINGS, and INSTRUCTIONS included with or attached to each product. Enerpac cannot be responsible for damage resulting from unsafe use of product, lack of maintenance, or incorrect product and system application. • Always wear proper personal protective gear (i.e. gloves, safety glasses). •…

OPERATION: Before lifting a load. The cylinder must be securely attached to the toe lift base. Keep the contact surface between the toe lift and the load clean. The contact surface must be free of oil, grease, or dirt to avoid slippage. Before lifting a load make sure that that the contact surface of the…

Enerpac machine lifts are built from a steel housing and a single-acting, spring return hydraulic cylinder. Powered by an external hand or electric pump, the cylinder plunger moves and actuates the machine lift. The support feet on the machine lift must be extended to provide maximum stability. To place the load skates, the load must…

HEAVY DUTY CATERROLLER™ LOAD SKATES STRAIGHT-LINE MOVES: Skates must remain parallel to each other to assure easiest motion in any one direction. Rigid-top skates will stay in position as placed, but swivel skates may be knocked out of alignment if the move is over a rough or dirty surface. Care should be taken, floors cleaned,…

HEAVY DUTY CATERROLLER™ LOAD SKATEs LIFTING LOADS: 1. Use load-lifting devices with a capacity exceeding the load weight and with enough lift height to safely install skates under the load. 2. Refer to the selection chart in the Enerpac catalog or the instruction sheets included with the skates for dimensions and skate load capacities. 3.…

HEAVY DUTY CATERROLLER™ LOAD SKATES FLOOR CONDITION AND PATHWAY CLEARANCES: 1. Floors or other path surfaces must be clean and free of cracks or holes, which can hinder skate travel. 2. Check and verify all load-bearing capacities of all floors or pathway surfaces. Ramps or other structures should be reinforced to handle the load. 3.…

HEAVY DUTY CATERROLLER™ LOAD SKATES CAUTION: Swivel type skates must be checked during moves to ensure parallel alignment under the load. WARNING: To prevent possible injury and equipment damage, do not exceed the rated capacities of the skates. LOAD REQUIREMENTS: 1. Determine the number of skates needed by calculating the total weight including support timbers,…

HEAVY DUTY CATERROLLER™ LOAD SKATES Load skates consist of a rigid steel frame with saw-toothed edges, a center guide plate and a set of rollers. The rollers are connected by link chain on either side with a master link for separating them. Each roller turns independently and the entire set rotates around the guide plate. Loads…

STB-SERIES PIPE BENDER SETS ASSEMBLY: 1. Fully thread the hydraulic cylinder into the cylinder support block on the bending frame. 2. Make sure that the saddle is fully threaded into the plunger fully hand tight. 3. Make all hose connections between the cylinder and hydraulic pump. Make sure that the coupler(s) are fully hand tightened.…

STB-Series hydraulic pipe bender sets are designed to provide quick, safe, and wrinkle-free bending of schedule 40, 80, 160, and DEH pipe in 1⁄2″ through 4″ sizes. STB-Series pipe bender sets include the Enerpac hydraulic cylinder, hose, and manual, air, or electric powered pump. Sets are also available without hydraulics. The bending frame and shoes are…